-
YRC-6BCD 8P15 Connection cable for Yaesu radios with AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR and AS-603UR Antenna Switch -
YRC-6BCD 10P15 Connection cable for Yaesu radios with AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR and AS-603UR Antenna Switch -
- Antenna Switch and Power Supply for two Rotators.
- Operation with Four Stack III Stack Match
-
IRC-12S Cable for connection between Icom radio and Hamplus MBD-12F, MBD-8G and MBD-62 controllers. -
IRC-6S Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Icom radio. -
YRC-6BCD15P15 Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR and AS-603UR with Yaesu radio. -
- Impedance matching for stack up to four antennas
- Controller for two rotators
- RS-232 Yaesu protocol for external rotator control
- Works with different rotators
- Wireless control
- All commands over RF cable
- Short circuit protection on RF cable
- Different array of antennas in TX and RX.
- HF operation
- Three installation options: Without the rotator power supply, with switch and rotator power supply in the same box, and with switch and rotator power supply in independent boxes.
- Works with a Controller for each Radio. Each Controller can access any of the antennas stack.
-
- Automatic Remote Antenna Switch with 6 antennas by 3 radios.
- Composed by the set AS-61RL and RC-603VR
- Works from 1.8 MHz to 148 MHz
- Control for two Rotors.
- Command over RF cable.
- RS-232 communication port
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX Radio or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
YRC-12 MP Cable for connection between Yaesu FTDX-101D, FTDX-101MP, FTDX-3000 radio and Hamplus MBD-12F, MBD-8G and MBD-62 Controllers -
Cable for connection pin to pin between Hamplus remote control MBD-62 and AS-62 Antenna Switcher, 20 meters long. -
Cable for connection pin to pin between Hamplus remote control MBD-62 and AS-62 Antenna Switcher, 15 meters long.
-
Cable for connection pin to pin between Hamplus remote control MBD-62 and AS-62 Antenna Switcher, 5 meters long.
-
Cable for connection pin to pin between Hamplus remote control MBD-8, MBD-12 and AS-82F, AS-84F, AS-86F, AS-1202F, AS-1204F, AS-1206F Antenna Switcher, 20 meters long.
-
Cable for connection pin to pin between Hamplus remote control MBD-8, MBD-12 and AS-82F, AS-84F, AS-86F, AS-1202F, AS-1204F, AS-1206F Antenna Switcher, 10 meters long.
-
Cable for connection pin to pin between Hamplus remote control MBD-8, MBD-12 and AS-82F, AS-84F, AS-86F, AS-1202F, AS-1204F, AS-1206F Antenna Switcher, 5 meters long.
-
FRC-8 Cable for connection between Hamplus remote control MBD-8E / F and Flex radio. -
FRC-6 Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Flex radio. -
- Power Supply for two Rotators.
- Automatic operation with: AS-603HL, AS-603VR, AS-603UR and Four Stack III
-
- Automatic Remote Antenna Switch with 6 antennas by 3 radios.
- Composed of the AS-61VR and RC-603VR set.
- Works on HF, VHF and UHF
- Control for two Rotators.
- Command over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX Radio or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
-
Automatic Remote Antenna Switch with 6 antennas by 3 radios and one linear amplifier.
- Composed by the set AS-61RL and RC-603RL
- HF 6m operation.
- Control for two Rotators.
- Command over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port.
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
-
The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control. -
The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control.
-
Cable for connection pin to pin between Hamplus remote control MBD-62 and AS-62 Antenna Switcher, 9 meters long.
-
Keypad
