-
Cable for connection pin to pin between Hamplus remote control MBD-62 and AS-62 Antenna Switcher, 20 meters long. -
Cable for connection pin to pin between Hamplus remote control MBD-62 and AS-62 Antenna Switcher, 5 meters long.
-
Cable for connection pin to pin between Hamplus remote control MBD-62 and AS-62 Antenna Switcher, 9 meters long.
-
Power Distributor -
ERC-12 Cable for connection between Elecraft radio and Hamplus remote control MBD-12F, MBD-8G and MBD-62. -
ERC-6 Cable for connection between Hamplus antenna Switch AS-603A / AS-603AL / AS-603WL / AS-603HR / AS-603VR / AS-603UR and Elecraft radio. -
ERC-8 Cable for connection between Hamplus remote control MBD-8E / F and Elecraft radio. -
The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control. -
The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control.
-
- Impedance matching for stack up to four antennas
- Controller for two rotators
- RS-232 Yaesu protocol for external rotator control
- Works with different rotators
- Wireless control
- All commands over RF cable
- Short circuit protection on RF cable
- Different array of antennas in TX and RX.
- HF operation
- Three installation options: Without the rotator power supply, with switch and rotator power supply in the same box, and with switch and rotator power supply in independent boxes.
- Works with a Controller for each Radio. Each Controller can access any of the antennas stack.
-
- Impedance matching for stack up to four antennas
- Controller for two rotators
- Antenna Switch and Power Supply in the same box
- RS-232 Yaesu protocol for external rotator control
- Works with different rotators
- Wireless control
- All commands over RF cable
- Short circuit protection on RF cable
- Different array of antennas in TX and RX.
- HF operation
- Three installation options: Without the rotator power supply, with switch and rotator power supply in the same box, and with switch and rotator power supply in independent boxes.
- Works with a Controller for each Radio. Each Controller can access any of the antennas stack.
-
FRC-12 Cable for connection between Hamplus remote control MBD-8G / MBD-12F / MBD-62 and Flex radio. -
FRC-6 Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Flex radio.
-
FRC-8 Cable for connection between Hamplus remote control MBD-8E / F and Flex radio. -
- Antenna Switch and Power Supply for two Rotators.
- Operation with Four Stack III Stack Match
-
Keypad -
Interface DI-12LH for connection between Hamplus remote control MBD-8g or MBD-12F with -
Interface DXE-419 for connection between Hamplus remote control MBD-8F or MBD-12F and DXEngineering DXE-419 Band Pass Filter -
IRC-12 Cable for connection between Icom radio and Hamplus MBD-12F, MBD-8G and MBD-62 controllers. -
IRC-12-13P Cable for connection between Hamplus MBD-12F, MBD-8G, MBD-62 controllers and Icom radio with 13 pin ACC connector.
-
IRC-12S Cable for connection between Icom radio and Hamplus MBD-12F, MBD-8G and MBD-62 controllers.
-
IRC-6 Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Icom radio. -
IRC-6-13P Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Icom radio with 13 pin ACC conector. -
IRC-62-13P Cable for connection between Hamplus antenna switch AS-603VR, AS-603UR and Icom radio with 13 pin ACC conector.
