The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control. -
The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control. -
- Automatic Remote Antenna Switch with 6 antennas by 3 radios.
- Composed by the set AS-61RL and RC-603VR
- Works from 1.8 MHz to 148 MHz
- Control for two Rotors.
- Command over RF cable.
- RS-232 communication port
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX Radio or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
- Impedance matching for stack up to four antennas
- Controller for two rotators
- RS-232 Yaesu protocol for external rotator control
- Works with different rotators
- Wireless control
- All commands over RF cable
- Short circuit protection on RF cable
- Different array of antennas in TX and RX.
- HF operation
- Three installation options: Without the rotator power supply, with switch and rotator power supply in the same box, and with switch and rotator power supply in independent boxes.
- Works with a Controller for each Radio. Each Controller can access any of the antennas stack.
-
-
Automatic Remote Antenna Switch with 6 antennas by 3 radios and one linear amplifier.
- Composed by the set AS-61RL and RC-603RL
- HF 6m operation.
- Control for two Rotators.
- Command over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port.
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
-
- Antenna Switch with 8 inputs by two output remotely controlled.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) for the R.F connections and DB-25 for remote control.
- All antenna inputs are switched to ground when not in use.
- When the power are switched off, all antenna inputs are routed to ground for protection purposes.
-
- Automatic Remote Antenna Switch with 6 antennas by 3 radios and one linear amplifier.
- Composed by the set AS-61WL and RC-603WL
- Works from 1.8 MHz to 54 MHz
- Command and power over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port.
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
Rotator Switch 2x4 If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, then Rotator Switch RS-24 is the solution. With it you will use only one controller on the table and it will be able to control till four antenna rotators.- The RS-24 can select between four rotators using only one controller for each shack.
- The system can use till two controllers.
- One interlock system don't permit connections for rotators in use on other shack.
- It is possible to automate all station.
- On systems where the Hamplus MBD-8E / F or MBD-12F is installed, the rotator assigned to each antenna are called on each change.
- The RS-24 comutates eight wires.
-
- Smart control for up to twelve Antenna and eight Rotator Switch.
- Band pass filter drive.
- Band Data Output.
- Automatic tuning for shortened antennas with high Q coils.
- Control with auxiliar keyboard for Waller Flag Receiving antennas manufactured by TOPBEAM.
- Eight rotator Switch control
- Antenna memory per Band
- Decoder with 31 bands from 100KHz to 10GHz
- GPI/O to control external equipments
- GPO Driven by frequency
- Hot Switch Protection
- Antenna Group protection to prevent another radio from using one of the antennas in the group
- No computer or software involved (PC less)
- Interlock system to prevent more then on radio at the same antenna.
- LAN for external remote control.
- Control all Hamplus (or others) antenna switch and rotator switch.
- Iluminated push buttons with labels.
- Software updates via USB.
-
- Antenna Switch with 6 inputs by two output remotely controlled.
- Aluminum cabinet painted in black color, having N or UHF type (SO-239) for the R.F connections and DB-15 for remote control.
- When the power are switched off, all antenna inputs are routed to ground.
- Operation from DC to 450MHz
-
- Intelligent control for up to two radios and six antennas with simultaneous operation.
- Memory of antennas with 22 bands that cover from 100 KHz to 450 MHz
- Two Band decoders
- Two outputs for triggering Band Pass Filters, one for each radio
- GPOs for automatic adjustment of shortened antennas with high Q coils
- Illuminated push buttons with ID tags
- RS-232 port for external control by personal computer
- LAN port for remote operation
- Software updates via USB.
- Interlock system that prevents two radios on the same antenna
- Split antenna operation, one antenna transmits and one receives
- Hot Switch Protection
- No computer or software is required (no PC)
- Compatible with all Hamplus antenna switch
- Suitable for use with the Hamplus antenna switch model AS-62
-
- Automatic Antenna Switch with 6 antennas by 3 radios and one linear amplifier.
- Inteligent band decoder and antenna memory.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) connections and DC 14v.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
- Antenna Switch with 6 inputs by two output remotely controlled.
- Aluminum cabinet painted in black color, having UHF type (SO-239) for the R.F connections and DB-15 for remote control.
- All antenna inputs are switched to ground when not in use.
- When the power are switched off, all antenna inputs are routed to ground for protection purposes.