The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control. -
The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control. -
If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, then Rotator Switch RS-44 is the solution. With it you will use only one controller on the table and it will be able to control till four antenna rotators.- The RS-44 can select between four rotators using only one controller for each shack.
- The system can use till four controllers.
- It is possible to automate all station.
- The RS-44 comutates eight wires.
- On systems where the Hamplus MBD-8F or MBD-12F is installed, the rotator assigned to each antenna are called on each change.
- One interlock system don't permit connections for rotators in use on other shack.
-
- Automatic Remote Antenna Switch with 6 antennas by 3 radios and one linear amplifier.
- Composed by the set AS-61WL and RC-603WL
- Works from 1.8 MHz to 54 MHz
- Command and power over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port.
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
- Antenna switch with 8 inputs by one output remotely controlled.
- Aluminum cabinet painted in the white color especially developed to allow external assembly.
- The coaxial connectors are the UHF type (SO-239) or N type for remote control.
- All unused inputs are automatically connected to ground.
- When the power supply are disconected, all inputs are connected to ground.
-
- Antenna switch with 8 inputs by one output.
- DC to 450MHz operation.
- The coaxial connectors are the UHF type (SO-239) or N type.
- When the power supply are disconected, all antennas are connected to ground.
-
Cable for connection pin to pin between Hamplus remote control MBD-62 and AS-62 Antenna Switcher, 20 meters long. -
Cable for connection pin to pin between Hamplus remote control MBD-62 and AS-62 Antenna Switcher, 15 meters long.
-
Cable for connection pin to pin between Hamplus remote control MBD-62 and AS-62 Antenna Switcher, 5 meters long.
-
Cable for connection pin to pin between Hamplus remote control MBD-8, MBD-12 and AS-82F, AS-84F, AS-86F, AS-1202F, AS-1204F, AS-1206F Antenna Switcher, 20 meters long.
-
Cable for connection pin to pin between Hamplus remote control MBD-8, MBD-12 and AS-82F, AS-84F, AS-86F, AS-1202F, AS-1204F, AS-1206F Antenna Switcher, 15 meters long.
-
Cable for connection pin to pin between Hamplus remote control MBD-8, MBD-12 and AS-82F, AS-84F, AS-86F, AS-1202F, AS-1204F, AS-1206F Antenna Switcher, 10 meters long.
-
Cable for connection pin to pin between Hamplus remote control MBD-8, MBD-12 and AS-82F, AS-84F, AS-86F, AS-1202F, AS-1204F, AS-1206F Antenna Switcher, 5 meters long.