-
Cable for connection pin to pin between Hamplus remote control MBD-8, MBD-12 and AS-82F, AS-84F, AS-86F, AS-1202F, AS-1204F, AS-1206F Antenna Switcher, 20 meters long. -
Cable for connection pin to pin between Hamplus remote control MBD-8, MBD-12 and AS-82F, AS-84F, AS-86F, AS-1202F, AS-1204F, AS-1206F Antenna Switcher, 10 meters long.
-
Cable for connection pin to pin between Hamplus remote control MBD-8, MBD-12 and AS-82F, AS-84F, AS-86F, AS-1202F, AS-1204F, AS-1206F Antenna Switcher, 5 meters long.
-
FRC-8 Cable for connection between Hamplus remote control MBD-8E / F and Flex radio. -
FRC-6 Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Flex radio. -
- Power Supply for two Rotators.
- Automatic operation with: AS-603HL, AS-603VR, AS-603UR and Four Stack III
-
- Automatic Remote Antenna Switch with 6 antennas by 3 radios.
- Composed of the AS-61VR and RC-603VR set.
- Works on HF, VHF and UHF
- Control for two Rotators.
- Command over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX Radio or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
-
Automatic Remote Antenna Switch with 6 antennas by 3 radios and one linear amplifier.
- Composed by the set AS-61RL and RC-603RL
- HF 6m operation.
- Control for two Rotators.
- Command over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port.
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
-
The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control. -
The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control.
-
Cable for connection pin to pin between Hamplus remote control MBD-62 and AS-62 Antenna Switcher, 9 meters long.
-
Keypad -
Power Distributor -
Interface DXE-419 for connection between Hamplus remote control MBD-8F or MBD-12F and DXEngineering DXE-419 Band Pass Filter -
- Connect your radio's RS-232 serial port to a PC with Logger Software and an MBD-8, MBD-12 controller or any other Hamplus automatic antenna switch.
- Applicable to Elecraft, Kenwood, Flex and other radios.
-
IRC-8-13P Cable for connection between Hamplus remote control MBD-8E / F and Icom radio with 13 pin ACC conector.
-
IRC-6-13P Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Icom radio with 13 pin ACC conector. -
- Intelligent control for up to two radios and six antennas with simultaneous operation.
- Memory of antennas with 22 bands that cover from 100 KHz to 450 MHz
- Two Band decoders
- Two outputs for triggering Band Pass Filters, one for each radio
- GPOs for automatic adjustment of shortened antennas with high Q coils
- Illuminated push buttons with ID tags
- RS-232 port for external control by personal computer
- LAN port for remote operation
- Software updates via USB.
- Interlock system that prevents two radios on the same antenna
- Split antenna operation, one antenna transmits and one receives
- Hot Switch Protection
- No computer or software is required (no PC)
- Compatible with all Hamplus antenna switch
- Suitable for use with the Hamplus antenna switch model AS-62
-
YRC-12 Cable for connection between Yaesu radio and Hamplus MBD-12F, MBD-8G and MBD-62 Controllers -
YRC-61 is a TTL to RS-232 converter cable for connection between Hamplus antenna switch and Yaesu radios compatible with model FT-847. -
YRC-6 Connection cable for Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR , AS-603UR and Yaesu radios. -
YRC-8 Cable for connection between Hamplus remote control MBD-8E / F and Yaesu radio. -
KRC-12 Cable for connection between Kenwood radio and Hamplus MBD-12F, MBD-8G and MBD-62 Controllers. -
KRC-6 Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL AS-603HR, AS-603VR, AS-603UR with Kenwood radio. -
KRC-8 Cable for connection between Hamplus remote control MBD-8E / F and Kenwood radio. -
IRC-12 Cable for connection between Icom radio and Hamplus MBD-12F, MBD-8G and MBD-62 controllers. -
IRC-6 Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Icom radio. -
IRC-8 Cable for connection between Hamplus remote control MBD-8E / F and Icom radio.
-
ERC-12 Cable for connection between Elecraft radio and Hamplus remote control MBD-12F, MBD-8G and MBD-62. -
ERC-6 Cable for connection between Hamplus antenna Switch AS-603A / AS-603AL / AS-603WL / AS-603HR / AS-603VR / AS-603UR and Elecraft radio. -
ERC-8 Cable for connection between Hamplus remote control MBD-8E / F and Elecraft radio. -
- Antenna and Rotator Switch with 2 inputs by one output remotely controlled.
- Coaxial connectors UHF type (SO-239) and DB-9 for rotators.
- Used to expand 8 to 16 antennas and 4 to 8 rotators.
- The ASR-21 comutates four wires.
-
- Antenna Switcher with 2 inputs by one output remotely controlled.
- The coaxial connectors are the UHF type (SO-239)
- Used to expand 8 to 16 antennas.
- Works with two AS-81 or others 8 ant. switch
-
Sale!
- Antenna Switch with 12 inputs by 6 output remotely controlled.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) for the R.F connections and DB-25 for remote control.
- All antenna inputs are switched to ground when not in use.
- When the power are switched off, all antenna inputs are routed to ground for protection purposes.
-
- Antenna Switch with 12 inputs by four output remotely controlled.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) for the R.F connections and DB-25 for remote control.
- All antenna inputs are switched to ground when not in use.
- When the power are switched off, all antenna inputs are routed to ground for protection purposes.
