-
The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control. -
- Antenna switch with 8 inputs by one output remotely controlled.
- Aluminum cabinet painted in the white color especially developed to allow external assembly.
- The coaxial connectors are the UHF type (SO-239) or N type for remote control.
- All unused inputs are automatically connected to ground.
- When the power supply are disconected, all inputs are connected to ground.
-
- Automatic Remote Antenna Switch with 6 antennas by 3 radios and one linear amplifier.
- Composed by the set AS-61WL and RC-603WL
- Works from 1.8 MHz to 54 MHz
- Command and power over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port.
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
Rotator Switch 2x4 If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, then Rotator Switch RS-24 is the solution. With it you will use only one controller on the table and it will be able to control till four antenna rotators.- The RS-24 can select between four rotators using only one controller for each shack.
- The system can use till two controllers.
- One interlock system don't permit connections for rotators in use on other shack.
- It is possible to automate all station.
- On systems where the Hamplus MBD-8E / F or MBD-12F is installed, the rotator assigned to each antenna are called on each change.
- The RS-24 comutates eight wires.
-
If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, the Rotator Switch RS-28 is the solution. With it you will use only one controller on the table and it will be able to control till eight antenna rotators.- The RS-28 can select between eight rotators using only one controller for each shack.
- The system can use till two controllers.
- One interlock system don't permit connections for rotators in use on other shack.
- It is possible to automate all station.
- On systems where the Hamplus MBD-12F is installed, the rotator assigned to each antenna are called on each change.
- The RS-28 comutates eight wires.
-
If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, then Rotator Switch RS-44 is the solution. With it you will use only one controller on the table and it will be able to control till four antenna rotators.- The RS-44 can select between four rotators using only one controller for each shack.
- The system can use till four controllers.
- It is possible to automate all station.
- The RS-44 comutates eight wires.
- On systems where the Hamplus MBD-8F or MBD-12F is installed, the rotator assigned to each antenna are called on each change.
- One interlock system don't permit connections for rotators in use on other shack.
-
If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, then Rotator Switch RS-48 is the solution. With it you will use only one controller on the table and it will be able to control till eight antenna rotators.The RS-48 can select between eight rotators using only one controller for each shack. The system can use till four controllers. One interlock system don't permit connections for rotators in use on other shack. It is possible to automate all station. On systems where the Hamplus MBD-12F is installed, the rotator assigned to each antenna are called on each change. The RS-48 comutates eight wires. -
- Smart control for up to twelve Antenna and eight Rotator Switch.
- Band pass filter drive.
- Band Data Output.
- Automatic tuning for shortened antennas with high Q coils.
- Control with auxiliar keyboard for Waller Flag Receiving antennas manufactured by TOPBEAM.
- Eight rotator Switch control
- Antenna memory per Band
- Decoder with 31 bands from 100KHz to 10GHz
- GPI/O to control external equipments
- GPO Driven by frequency
- Hot Switch Protection
- Antenna Group protection to prevent another radio from using one of the antennas in the group
- No computer or software involved (PC less)
- Interlock system to prevent more then on radio at the same antenna.
- LAN for external remote control.
- Control all Hamplus (or others) antenna switch and rotator switch.
- Iluminated push buttons with labels.
- Software updates via USB.
-
Manual Remote Control The RC-12 ia a manual remote control unit, used to control antenna switches up to 12 antennas. It features interlock, not allowing more than one radio in the same antenna. The actuator is a rotating switch and there are LED´s indicators for confirmation. On the side of each LED you will find a white space to take a note about each antenna. Recommended for more than one radio use. -
- Automatic Antenna Switch with 6 antennas by 3 radios.
- Inteligent band decoder and antenna memory.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) connections and DC 14v.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation compatible with any radio.
-
- Antenna Switch with 8 inputs by two output remotely controlled.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) for the R.F connections and DB-25 for remote control.
- All antenna inputs are switched to ground when not in use.
- When the power are switched off, all antenna inputs are routed to ground for protection purposes.
-
- Antenna switch with 8 inputs by 4 output remotely controlled.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) for the R.F connections and DB-25 for remote control.
- All antenna inputs are switched to ground when not in use.
- When the power are switched off, all antenna inputs are routed to ground for protection purposes.
