-
-
Automatic Remote Antenna Switch with 6 antennas by 3 radios and one linear amplifier.
- Composed by the set AS-61RL and RC-603RL
- HF 6m operation.
- Control for two Rotators.
- Command over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port.
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
-
- Power Supply for two Rotators.
- Automatic operation with: AS-603HL, AS-603VR, AS-603UR and Four Stack III
-
- Antenna Switch and Power Supply for two Rotators.
- Operation with Four Stack III Stack Match
-
- Automatic Remote Antenna Switch with 6 antennas by 3 radios.
- Composed of the AS-61VR and RC-603VR set.
- Works on HF, VHF and UHF
- Control for two Rotators.
- Command over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX Radio or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
- Automatic Remote Antenna Switch with 6 antennas by 3 radios.
- Composed by the set AS-61RL and RC-603VR
- Works from 1.8 MHz to 148 MHz
- Control for two Rotors.
- Command over RF cable.
- RS-232 communication port
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX Radio or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
- Automatic Antenna Switch with 6 antennas by 3 radios and one linear amplifier.
- Inteligent band decoder and antenna memory.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) connections and DC 14v.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
- Automatic Antenna Switch with 6 antennas by 1 radio
- DC to 450 MHz operation
- RS-232 Com
- Inteligent band decoder and antenna memory.
- Cabinet painted in the black color, having UHF type (SO-239) connections and DC 13.8v.
- All antennas and radio are switched to ground when not in use.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
Rotator Switch 2x4 If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, then Rotator Switch RS-24 is the solution. With it you will use only one controller on the table and it will be able to control till four antenna rotators.- The RS-24 can select between four rotators using only one controller for each shack.
- The system can use till two controllers.
- One interlock system don't permit connections for rotators in use on other shack.
- It is possible to automate all station.
- On systems where the Hamplus MBD-8E / F or MBD-12F is installed, the rotator assigned to each antenna are called on each change.
- The RS-24 comutates eight wires.
-
If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, the Rotator Switch RS-28 is the solution. With it you will use only one controller on the table and it will be able to control till eight antenna rotators.- The RS-28 can select between eight rotators using only one controller for each shack.
- The system can use till two controllers.
- One interlock system don't permit connections for rotators in use on other shack.
- It is possible to automate all station.
- On systems where the Hamplus MBD-12F is installed, the rotator assigned to each antenna are called on each change.
- The RS-28 comutates eight wires.
-
If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, then Rotator Switch RS-48 is the solution. With it you will use only one controller on the table and it will be able to control till eight antenna rotators.The RS-48 can select between eight rotators using only one controller for each shack. The system can use till four controllers. One interlock system don't permit connections for rotators in use on other shack. It is possible to automate all station. On systems where the Hamplus MBD-12F is installed, the rotator assigned to each antenna are called on each change. The RS-48 comutates eight wires. -
- Connect your radio's RS-232 serial port to a PC with Logger Software and an MBD-8, MBD-12 controller or any other Hamplus automatic antenna switch.
- Applicable to Elecraft, Kenwood, Flex and other radios.
-
Manual Remote Control The RC-12 ia a manual remote control unit, used to control antenna switches up to 12 antennas. It features interlock, not allowing more than one radio in the same antenna. The actuator is a rotating switch and there are LED´s indicators for confirmation. On the side of each LED you will find a white space to take a note about each antenna. Recommended for more than one radio use.
