-
-
Automatic Remote Antenna Switch with 6 antennas by 3 radios and one linear amplifier.
- Composed by the set AS-61RL and RC-603RL
- HF 6m operation.
- Control for two Rotators.
- Command over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port.
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
-
- Power Supply for two Rotators.
- Automatic operation with: AS-603HL, AS-603VR, AS-603UR and Four Stack III
-
- Antenna Switch and Power Supply for two Rotators.
- Operation with Four Stack III Stack Match
-
- Automatic Remote Antenna Switch with 6 antennas by 3 radios.
- Composed of the AS-61VR and RC-603VR set.
- Works on HF, VHF and UHF
- Control for two Rotators.
- Command over RF cable.
- Short circuit protection on RF cable
- RS-232 communication port
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX Radio or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
- Automatic Remote Antenna Switch with 6 antennas by 3 radios.
- Composed by the set AS-61RL and RC-603VR
- Works from 1.8 MHz to 148 MHz
- Control for two Rotors.
- Command over RF cable.
- RS-232 communication port
- Inteligent band decoder and antenna memory.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX Radio or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
- Automatic Antenna Switch with 6 antennas by 3 radios and one linear amplifier.
- Inteligent band decoder and antenna memory.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) connections and DC 14v.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
- Automatic Antenna Switch with 6 antennas by 1 radio
- DC to 450 MHz operation
- RS-232 Com
- Inteligent band decoder and antenna memory.
- Cabinet painted in the black color, having UHF type (SO-239) connections and DC 13.8v.
- All antennas and radio are switched to ground when not in use.
- Automatic operation compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation with any radio.
-
Rotator Switch 2x4 If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, then Rotator Switch RS-24 is the solution. With it you will use only one controller on the table and it will be able to control till four antenna rotators.- The RS-24 can select between four rotators using only one controller for each shack.
- The system can use till two controllers.
- One interlock system don't permit connections for rotators in use on other shack.
- It is possible to automate all station.
- On systems where the Hamplus MBD-8E / F or MBD-12F is installed, the rotator assigned to each antenna are called on each change.
- The RS-24 comutates eight wires.
-
If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, the Rotator Switch RS-28 is the solution. With it you will use only one controller on the table and it will be able to control till eight antenna rotators.- The RS-28 can select between eight rotators using only one controller for each shack.
- The system can use till two controllers.
- One interlock system don't permit connections for rotators in use on other shack.
- It is possible to automate all station.
- On systems where the Hamplus MBD-12F is installed, the rotator assigned to each antenna are called on each change.
- The RS-28 comutates eight wires.
-
If you have more than one radio room (Shack) and/or more than one Rotator on your directional antennas, then Rotator Switch RS-48 is the solution. With it you will use only one controller on the table and it will be able to control till eight antenna rotators.The RS-48 can select between eight rotators using only one controller for each shack. The system can use till four controllers. One interlock system don't permit connections for rotators in use on other shack. It is possible to automate all station. On systems where the Hamplus MBD-12F is installed, the rotator assigned to each antenna are called on each change. The RS-48 comutates eight wires. -
- Connect your radio's RS-232 serial port to a PC with Logger Software and an MBD-8, MBD-12 controller or any other Hamplus automatic antenna switch.
- Applicable to Elecraft, Kenwood, Flex and other radios.
-
Manual Remote Control The RC-12 ia a manual remote control unit, used to control antenna switches up to 12 antennas. It features interlock, not allowing more than one radio in the same antenna. The actuator is a rotating switch and there are LED´s indicators for confirmation. On the side of each LED you will find a white space to take a note about each antenna. Recommended for more than one radio use. -
- Automatic Antenna Switch with 6 antennas by 3 radios.
- Inteligent band decoder and antenna memory.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) connections and DC 14v.
- All antennas and radios are switched to ground when not in use.
- Non-simultaneous operation.
- Compatible with: ELECRAFT, KENWOOD, YAESU, ICOM, FLEX or any other Radio that uses one of these communication protocols.
- Manual operation compatible with any radio.
-
The "Four Stack II" system from Hamplus allows one array of antennas for simultaneous operation. It is possible operate with two, three or four antennas.
For each set of antennas of the same band, two devices are used, the switch box and the remote control. -
- Antenna switch with 8 inputs by 6 output remotely controlled.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) for the R.F connections and DB-25 for remote control.
- All antenna inputs are switched to ground when not in use.
- When the power are switched off, all antenna inputs are routed to ground for protection purposes.
-
Sale!
- Antenna Switch with 12 inputs by 6 output remotely controlled.
- Aluminum cabinet painted in the dark gray color, having UHF type (SO-239) for the R.F connections and DB-25 for remote control.
- All antenna inputs are switched to ground when not in use.
- When the power are switched off, all antenna inputs are routed to ground for protection purposes.
-
- Antenna Switcher with 2 inputs by one output remotely controlled.
- The coaxial connectors are the UHF type (SO-239)
- Used to expand 8 to 16 antennas.
- Works with two AS-81 or others 8 ant. switch
-
- Antenna and Rotator Switch with 2 inputs by one output remotely controlled.
- Coaxial connectors UHF type (SO-239) and DB-9 for rotators.
- Used to expand 8 to 16 antennas and 4 to 8 rotators.
- The ASR-21 comutates four wires.
-
ERC-8 Cable for connection between Hamplus remote control MBD-8E / F and Elecraft radio. -
ERC-6 Cable for connection between Hamplus antenna Switch AS-603A / AS-603AL / AS-603WL / AS-603HR / AS-603VR / AS-603UR and Elecraft radio. -
ERC-12 Cable for connection between Elecraft radio and Hamplus remote control MBD-12F, MBD-8G and MBD-62. -
IRC-8 Cable for connection between Hamplus remote control MBD-8E / F and Icom radio. -
FRC-8 Cable for connection between Hamplus remote control MBD-8E / F and Flex radio.
-
FRC-12 Cable for connection between Hamplus remote control MBD-8G / MBD-12F / MBD-62 and Flex radio. -
IRC-8-13P Cable for connection between Hamplus remote control MBD-8E / F and Icom radio with 13 pin ACC conector.
-
IRC-6 Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Icom radio. -
IRC-6S Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Icom radio.
-
FRC-6 Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Flex radio.
-
IRC-62-13P Cable for connection between Hamplus antenna switch AS-603VR, AS-603UR and Icom radio with 13 pin ACC conector. -
IRC-6-13P Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL, AS-603HR, AS-603VR, AS-603UR and Icom radio with 13 pin ACC conector.
-
IRC-12 Cable for connection between Icom radio and Hamplus MBD-12F, MBD-8G and MBD-62 controllers. -
IRC-12S Cable for connection between Icom radio and Hamplus MBD-12F, MBD-8G and MBD-62 controllers.
-
IRC-12-13P Cable for connection between Hamplus MBD-12F, MBD-8G, MBD-62 controllers and Icom radio with 13 pin ACC connector.
-
KRC-8 Cable for connection between Hamplus remote control MBD-8E / F and Kenwood radio. -
KRC-6 Cable for connection between Hamplus antenna switch AS-603A, AS-603AL, AS-603WL AS-603HR, AS-603VR, AS-603UR with Kenwood radio. -
KRC-12 Cable for connection between Kenwood radio and Hamplus MBD-12F, MBD-8G and MBD-62 Controllers.
